Join our mailing list!



Knowledge Base:  
You are here: Knowledge Base > Graphics Gallery
Timed deposits of a 2-part epoxy direct from the dual cartridge using an ADL810 dispenser, TS1212 valve and pneumatic gun
Last Updated: 17/10/2012
Timed shots from a 2-part epoxy type side by side cartridge
Bench mounted system for dispensing dual epoxies in 50ml, 200ml or 400ml (1:1, 2:1, 4:1 or 10:1 ratio). The ADL810 dispenser contols the TS1212 pinch valve. Mixed epoxy is fed under pressure from the modified pneumatic gun. A luer fitting is used on the end of the static mixer nozzle to feed directly into the disposable pinch tube on the TS1212 valve. As the ADL810 foot pedal is pressed, the TS1212 opens to allow the epoxy to flow. The ADL810 can be set to make repeat consistent shots or on steady mode for beads or potting. This system offers hands free dispensing. Tubes on the TS1212 as well as the mixer nozzle and the luer adapter are easily replaced. This system allows for standard dual epoxy cartridges to be dispensed directly from the tubes. System is supplied complete.

Timed shots from a epoxy 2 component cartridge

Was this article helpful?

Comments:
 

Related Articles
 > Typical dual Pinch Valve dispensing system from 500 gram Pressure Pot with digital controller
 > Typical dual TS1212 dispensing system with dual syringe reservoirs, Controlled by digital dispenser
 > Typical cartridge dispense station using 6oz. Techkit & 918 cap assembly. Controlled by TS924.
 > Typical two part adhesive dispensing using TS1212 valve controlled by digital dispenser
 > Typical cartridge to syringe filling station with stand controlled by a TS924 foot valve
 > Typical TS1212 dispense system controlled by ADL810 dispenser
 > Typical TS941 Spool Valve fed by a TS918-20 production master system controlled by a TS250 dispenser
 > Typical TS941 syringe filling system fed by a TS918-20 production master system controlled by a TS250 dispenser
 > TS941 Spool Valve with material supply from TS918-60 Production Master System controlled by TS250 dispenser
 > Typical TS918-20 20oz Production Master System controlled by a TS924V Foot valve
 > TS918 Production Master System with assorted cartridge retainer sets controlled by a TS924V Foot valve
 > TS934A or TS941A Spool Valve controlled by TS350 dispenser
 > TS941A Spool Valve used for cartridge filling controlled by a TS924 Foot valve
 > TS941A Spool Valve supplied from a TS1263 pressure vessel controlled by a TS250 dispenser
 > TS1201 Pinch Valve Pen application with material supplied from TS1215 pressure pot
 > Cartridge based system using a TS918-110 system controlled by a TS250 dispenser
 > Two part adhesive dispensing system with TS1212 valve or TS1201 pen controlled by TS250 dispenser
 > Two part adhesive dispensing system with TS1212 valve controlled by TS350 dispenser
 > TS1212 QUAD System controlled by (2) TS350 dispensers. Fed by a modified TS1258.
 > TS5622VU diaphragm valves (4) controlled by TS500R controllers (4) supplied by pressure pot
 > TS1212 valve supplied by TS125 pressure pot controlled by TS250 dispenser
 > TS1212 valve dispense system supplied by a 30cc syringe controlled by TS250
 > TS1212 valve dispense system supplied by a 20oz cartridge controlled by TS250
 > TS941A valve dispense system supplied by a 12oz cartridge controlled by TS250
 > TS1201 (2) pen valves supplied from pressure pot divided by liquid manifold
 > Cartridge to dual syringe filling station from TS924 footvalve dispenser
 > High pressure silicone to valve dispense system non timed from bulk supply
 > Gravity fed CA adhesive dispense system using TS1201 pen valve
 > TS924 epoxy syringe filling station from pneumatic dual cartridge gun
 > TS5000 Auger Valve remote feed from a 20oz. or 1/10 Gal cartridge using TS500R controller
 > Paste syringe filling station using TS941A high pressure valve fed by customers own bulk supply
 > 4 unit dispense station using TS941 Spool Valves supplied by 12oz cartridges controlled by 2 TS350 dispensers
 > Epoxy dual cartridge setup with a TS1212 valve controlled by a TS250 dispenser
 > 20oz cartridge reservoir system on bench stand supplying TS1201 handheld pen valve
 > TS5622VU CA dispense valve dispense system fed by TS1215 pressure pot with TS350 controller
 > TS9180-110 (2) Production Master Systems with TS941 (2) Spool Valve controlled by TS350
 > 3 person high pressure TS941 spool valve system operated by TS924 footvalves
 > Syringe dispense station controlled by a non timed TS924 Foot Valve
 > Dual TS1212 valve dispensing station controlled by TS500R fed from TS1265 pressure pot
 > Pneumatic TS924 footvalve dispenser controlling 2.5oz cartridge feed system
 > TS1201 dispense pen application fed from a 2 gal pressure Pot.
 > Dual TS5420 needle valves supplied by a 5 gal pail pump controlled by a TS350
 > 4 station dispense system using TS1201 pens fed from 1 gallon pressure pot
 > 2 station dispense system using TS1201 pens fed from 500gram pressure pot
 > TS5000 Auger Valve connection to a TS500R controller
 > TS5622VU diaphragm valve installation for use on an XYZ table controlled by a TS500R controller
 > Multiple TS5440 needle valve installation controlled by 3 TS350 controllers
 > TS918-80 production master system dispensing station controlled by a TS250
 > TS5622VU diaphragm valve system controlled by a TS250 dispenser fed by pressure pot.
 > TS5420 needle valve system controlled by a TS250 dispenser fed by TS1258 pressure pot
 > TS1201 Pinch pen fed from a TS918 retainer/cap assembly with nozzle
 > TS918-6 cartridge feeding a TS941A Spool Valve controlled by a TS250
 > TS5322 dispense station mounted on an XYZ table controlled by a TS500R
 > TS1212 Dispense System with remote feed controlled by a TS250
 > TS5622VU diaphragm valve controlled by TS250 controller material supply from 20oz cartridge assembly
 > 918-80 Production Master System utilizing a TS1212 Micro Shot Valve
 > TS1212 Micro Shot Valve supplied by a two gallon pressure vessel controlled by a TS9150
 > TS1212 micro shot valve fed by a TS918-20 production master system controlled by a TS250
 > Dual TS1201 disposable material path pen application supplied from TS1251 pressure pot
 > TS5420 needle valve system controlled by a TS250 dispenser fed by pressure pot
 > TS5622VT diaphragm valve controlled by a TS500R with material supplied by a 12oz cartridge retainer
 > Dual TS1212 dispense system from TS1215 pressure pot run by TS350
 > Typical bench mounted dual cartridge dispense system controlled by a TS924 foot valve
 > Syringe filling station using the TS918-110 production Master System controlled by a TS924 Foot Valve
 > Dispense station using the TS5420 fed from a TS1215 controlled by a TS250
 > TS5420 needle valve system controlled by a TS350 fed by TS1258
 > Manual dual cartridge gun with material line for dispense adapter
 > Manual dual cartridge gun with fittings for filling syringe barrels
 > TS941A spool valve fed by a 20oz cartridge system controlled by a TS250 dispenser
 > TS941 Spool Valve fed from a pressure pot ready to use with customers own dispenser
 > TS941 Spool Valve fed from a pressure pot run from TS350 dispenser
 > TS941 Spool Valve fed from a pressure pot controlled by an ADL810 dispenser
 > Syringe filling station using a 918-110 production master system
 > 6 TS1212 valve system controlled by a TS350 dispenser fed by a TS1255 pressure pot
 > Dual pneumatic cartridge gun feeding a TS1201 Pinch Tube Pen Valve
 > Cartridge dispense station using 6oz retainer & cap assembly controlled by TS924V
 > Vertical setup using dual cartridges a TS1212 valve and controlled by a TS350
 > TS5322 mini spool valve fed by a TS918-110 production master system controlled by a TS250
 > TS918-110 production master system controlled by a TS924 Foot Valve
 > TS918-60 production master system controlled by a TS924 Foot Valve
 > Bench mounted syringe dispense system controlled by a TS250
 > Spray Valve set-up using 6 TS5520 controlled by 6 TS500R fed from a TS1258 pressure pot
 > Spray Valve set-up using 2 TS5520 controlled by 2 TS500R fed from a TS1258 pressure pot
 > TS1215 tank using a TS1201 valve to dispense from a BT16 brush tip
 > TS1258 pressure pot using a TS5520 spray valve controlled by a TS5500R
 > TS918-6 cartridge feed to TS1212 pinch valve controlled with a TS924 dispenser
 > Dual TS5322 spool valves from TS1215 pressure pot controlled by TS350
 > TS5420 needle valve fed from TS1258 pressure pot controlled by TS350
 > TS5520 Spray Valve controlled by a TS500R fed from a TS1258 pressure dispenser
 > TS1212 syringe fill system for UV adhesives fed by a TS1215 pressure pot controlled by a TS250
 > Dual TS941A Valve controlled by a TS250 fed by a Pail Pump system
 > Dual TS1201 disposable material path pen application material supplied from TS1215 tank
 > TS918-110 production master system controlled by a TS924 toot valve
 > TS918 production master system with syringe bracket controlled by a TS924 dispenser
 > TS918-6 production master system using a TS5322 spool valve controlled by a TS250
 > Dual TS1212 dispensing system from TS1215 pressure pot controlled by two TS250's
 > 4 unit station using TS941 spool valves supplied by 20 oz cartridge controlled by TS350's
 > 2 unit dispense station using TS5322 valves mounted on TS918 Stands controlled by two TS250s
 > TS918-110 Dispense Station using a TS941 Spool Valve
 > Ram Elevator System feeding a TS941A Spool Valve controlled by a TS350 dispenser
 > Diaphragm valve setup controlled by a TS500R material supplied by TS1258
 > Syringe dispensing system using a 55cc syringe controlled by a TS350
 > Four TS5620HU diaphragm valves material fed from a TS1258 pressure pot valves controlled by TS250's
 > TS5520 spray valve set-up supplied by a 55cc syringe controlled by a TS500R
 > TS1258 with a TS1201 Dispense Pen
 > TS1258 with four TS1201 Dispense Pens via TS918-46 manifold
 > 2 TS5620HU diaphragm valves via manifold fed from a TS1258 pressure pot controlled by TS350
 > Dispense valve selector chart by valve type
 > TS5620 series diaphragm valve cutaway diagram
 > TS5540 series spray valve cutaway diagram
 > TS5322 series mini spool valve cutaway diagram
 > TS5000DMP series motor driven auger valve cutaway diagram
 > TS5420 series needle valve cutaway diagram
 > TS5440 series needle valve cutaway diagram
 > TS941/ TS941A series spool valve cutaway diagram
 > TS1212 series pinch tube valve cutaway diagram
 > Graphic of TS series ribbon nozzles for cartridges and valves
 > Graphic of typical valve setup showing pressure pot, controller and valve
 > Graphic of typical dispenser setup showing syringe barrel and dispense tip
 > 2 station dispense system on stand using TS1201 pens with manifold fed from 5 litre pressure pot
 > Four TS5622VU diaphragm valves from TS918-46 manifold and TS2250 pressure pot
 > Timed deposits of a 2-part epoxy direct from 1 400ml dual cartridge using a 1000T digital dispenser and modified pneumatic applicator
 > 4 station manual dispense system using TS1201 pens with manifold fed from PP300-A 500 gram clear body pressure pot
 > TS5540 series spray valve spare parts
 > TS5622 series diaphragm valve parts list