|
|
|
|
The TS5600 Series dispense valves accurately control the application of most low to medium viscosity fluids without drips. The unique seal-less design incorporates an inert polymer diaphragm that isolates the actuator from the valve. The adjustable open/close stroke 0.13 to 0.64 mm (0.005" to 0.025") allows for a very fast response with positive shutoff.
Wetted components are made of inert plastics. Takes a direct feed from any pressure pot, cartridge or syringe and includes a selection of flexible fluid line tubing and connectors. Valve open time can be as short as 15 milliseconds.
This Delrin valve is most suited to UV cure, solvents, water, inks, primers and activators. Please select the UHMW version (TS5622VU) for Cyanoacrylates. Use with the pneumatic dispenser/ controller.
Part ID: TS5622VD Wetted Materials: Delrin, Teflon Size: 76mm L x 27mm Dia. Weight: 118g (0.26lb) Viscosity Range: 1 - 50,000 CPS Repeatability: +/- 3% Cycle Rate: Up to 500 cycles/ minute Flow Rate (water): 7250ml/minute @ 100 psi Min Shot Size: 0.0075 cc/ ml Max Fluid Pressure: 70 psi ( 5 Bar) Activation Pressure: 70 psi (4.8 bar) minimum Material Inlet: 1/8" NPT Material Outlet: 1/4-28 UNF Mounting: 10-32 UNF Warranty: 1 Year Commodity Code: 90289090
Model TS5622VD with Delrin polymer wetted parts is used for dispensing UV cure, anaerobics and fluxes. Simple to use with any pneumatic dispenser/ controller. Fluid housing is in FDA-compliant Delrin for most dispensing applications. A UHMW version is available for chemical compatibility and a Teflon version for Cyanoacrylates. A stainless steel version with optimized internal fluid route is especially dedicated to dispense UV-cure adhesives, resins and lacquers used in the manufacture of DVDs and CDs. A hand-held actuated valve is also available.
Adhesive Dispensing Ltd provide a wide range of equipment options for dispensing almost all assembly fluids - from watery liquids, solvents, primers and activators through to thick pastes, sealants, silicones, gels and epoxies.
- Part ID: TS5622VD
- Wetted Materials: Delrin, Teflon
- Size: 76mm L x 27mm Dia..
- Weight: 118g (0.26lb)
- Viscosity Range: 1 - 50,000 CPS
- Repeatability: +/-3%
- Cycle Rate: Up to 500 cycles/ minute
- Flow Rate (water): 7250ml/minute @ 100 psi
- Min Shot Size: 0.0075 cc/ ml
- Max Fluid Pressure: 70 psi ( 5 Bar)
- Activation Pressure: 70 psi (4.8 bar) minimum
- Material Inlet: 1/8" NPT
- Material Outlet: 1/4-28 UNF
- Mounting: 10-32 UNF
- Warranty: 1 Year
Items are shipped by courier on a tracked
and insured service.
The
TS5622VD requires no regular maintenance other than the possible replacement of
the diaphragm disc after time. This is a low cost replacement part. Details of
spares for this valve can be found on our knowledge base by following this
link: https://www.adhesivedispensing.net/kb_results.asp?ID=265
Typical Applications:
Diaphragm
valves are used for many varied assembly and production processes where
controlled deposits of low to medium viscosity liquids need to be applied.
Common applications include:-
Deposits
of UV Cure
Deposits
of solvents
Deposits
of single part epoxies
Deposits
of primers
Deposits
of PVA glues
Deposits
of liquid fluxes
Deposits
of threadlockers
General
adhesive application
What's
Included? The TS5622VD valve is supplied with a starter kit. The parcel will
arrive with:- 1 x TS5622VD valve 1 x clear luer lock fluid line 1 x black luer
lock fluid line 5 x assorted dispense tips 1 x tip cap seal 1 x user guide.
|
|
|
|
|
|
|
|
|
|
|
|
|
Features
- Ideal for UV cure, anaerobics and many other fluids
- High precision solution supplied complete
- Repeat dots, lines or potting of most liquids
- Adjustable stroke control for fine tuning of flow
- Syringe feed, cartridge feed or pressure pot
- Supplied with fluid lines and tip kit
- Easy bench mount, machine mount or robot mount
- Simple to control using TS500R, TS250 or TS350
- 1 Year Warranty
|
|
|
|
|
|
|
|
|