 |
 |
 |
|
The TS5600 Series dispense valves accurately control the application of most low to medium viscosity fluids without drips. The unique seal-less design incorporates an inert polymer diaphragm that isolates the actuator from the valve. The adjustable open/close stroke 0.13 to 0.64 mm (0.005" to 0.025") allows for a very fast response with positive shutoff. Wetted components are made of inert plastics. Takes a direct feed from any pressure pot, cartridge or syringe and includes a selection of flexible fluid line tubing and connectors. Valve open time can be as short as 15 milliseconds.
Model TS5620HU with UHMW polymer wetted parts is used for dispensing solvents, cyanoacrylates, anaerobics and fluxes. Simple to use with any pneumatic dispenser/ controller.
* Ultra High Molecular Weight polyethylene.
Fluid housing is in FDA-compliant Ultra High Molecular Weight Polyethylene (UHMWPE) for most dispensing applications. A Teflon version is available for chemical compatibility and a Delrin version for UV-curable adhesives are also available. A stainless steel version with optimized internal fluid route is especially dedicated to dispense UV-cure adhesives, resins and lacquers used in the manufacture of DVDs and CDs. A hand-held actuated valve is also available.
Part ID: TS5620HU
Materials: UHMW, Teflon
Size: 61mm L x 24mm Dia.
Weight: 59g (0.13lb)
Viscosity Range: 1 - 50,000 CPS
Repeatability: +/- 0.30%
Cycle Rate: Up to 500 cycles/ minute
Flow Rate (water): 3432ml/minute @ 100 psi
Min Shot Size: 0.0075 cc/ ml
Max Fluid Pressure: 70 psi ( 5 Bar)
Activation Pressure: 70 psi (4.8 bar) minimum
Material Inlet: 1/4-28 UNF
Material Outlet: 1/4-28 UNF
Mounting: 10-32 UNF
Warranty: 1 Year
Commodity Code: 84248940
Adhesive Dispensing Ltd provide a wide range of equipment options for dispensing almost all assembly fluids - from watery liquids, solvents, primers and activators through to thick pastes, sealants, silicones, gels and epoxies.
- Part ID: TS5620HU
- Materials: UHMW, Teflon
- Size: 61mm L x 24mm Dia.
- Weight: 59g (0.13lb)
- Viscosity Range: 1 - 50,000 CPS
- Repeatability: �0.30%
- Cycle Rate: Up to 500 cycles/ minute
- Flow Rate (water): 3432ml/minute @ 100 psi
- Min Shot Size: 0.0075 cc/ ml
- Max Fluid Pressure: 70 psi ( 5 Bar)
- Activation Pressure: 70 psi (4.8 bar) minimum
- Material Inlet: 1/4-28 UNF
- Material Outlet: 1/4-28 UNF
- Mounting: 10-32 UNF
- Warranty: 1 Year
Items are shipped in the UK by Interlink Express on a next day tracked and insured service. For Europe deliveries, products are shipped via DPD or Air Express. For all international shipments, items are sent RM Signed-For or FedEx.
The TS5600 series require little maintenance other than the replacement of the fluid lines, input fittings and tips.
Typical Applications
Diaphragm valves are used for many varied assembly and production processes where controlled deposits of low to medium viscosity liquids need to be applied. Common applications include:-
Dots and beads of Cyanoacrylates
Dots and beads of solvents
Dots and beads of UV cure
Dots and beads of PVA glues
Deposits of liquid fluxes
Dots and beads of threadlockers
General adhesive application
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Ideal for cyanoacrylates, primers and activators
- High precision solution supplied complete
- Repeat dots, lines or potting of most liquids
- Adjustable stroke control for fine tuning of flow
- Syringe feed, cartridge feed or pressure pot
- Supplied with fluid lines and tip kit
- Easy bench mount, machine mount or robot mount
- Simple to control using TS500R, TS250 or TS350
|
|
|
|
|
|
|
|
|
