 |
 |
 |
|
The TS5600 Series dispense valves accurately control the application of most low to medium viscosity fluids without drips. The unique seal-less design incorporates an inert polymer diaphragm that isolates the actuator from the valve. The adjustable open/close stroke 0.13 to 0.64 mm (0.005" to 0.025") allows for a very fast response with positive shutoff.
Wetted components are made of inert plastics. Takes a direct feed from any pressure pot, cartridge or syringe and includes a selection of flexible fluid line tubing and connectors. Valve open time can be as short as 15 milliseconds. Model TS5622VU with UHMW* polymer wetted parts is used for dispensing solvents, cyanoacrylates, anaerobics and fluxes. Simple to use with pneumatic dispensers/ controllers.
*Ultra High Molecular Weight polyethylene.
Part ID: TS5622VU
Wetted Materials: UHMW, Teflon
Size: 76mm L x 27mm Dia.
Weight: 118g (0.26lb)
Viscosity Range: 1 - 50,000 CPS
Repeatability: +/- 0.30%
Cycle Rate: Up to 500 cycles/ minute
Flow Rate (water): 7250ml/minute @ 100 psi
Min Shot Size: 0.0075 cc/ ml
Max Fluid Pressure: 70 psi ( 5 Bar)
Activation Pressure: 70 psi (4.8 bar) Minimum
Material Inlet: 1/8" NPT
Material Outlet: 1/4-28 UNF
Mounting: 10-32 UNF
Warranty: 1 Year
Commodity Code: 84248940
Adhesive Dispensing Ltd provide a wide range of equipment options for dispensing almost all assembly fluids - from watery liquids, solvents, primers and activators through to thick pastes, sealants, silicones, gels and epoxies.
- Part ID: TS5622VU
- Wetted Materials: UHMW, Teflon�
- Size: 76mm L x 27mm Dia..
- Weight: 118g (0.26lb)
- Viscosity Range: 1 - 50,000 CPS
- Repeatability: �0.30%
- Cycle Rate: Up to 500 cycles/ minute
- Flow Rate (water): 7250ml/minute @ 100 psi
- Min Shot Size: 0.0075 cc/ ml
- Max Fluid Pressure: 70 psi ( 5 Bar)
- Activation Pressure: 70 psi (4.8 bar) minimum
- Material Inlet: 1/8" NPT
- Material Outlet: 1/4-28 UNF
- Mounting: 10-32 UNF
- Warranty: 1 Year
Items are shipped in the UK by tracked courier.
The TS5600 series require little maintenance other than the replacement
of the fluid lines, input fittings and tips.
Typical Applications Diaphragm valves are used for many varied assembly
and production processes where controlled deposits of low to medium viscosity
liquids need to be applied. Common applications include:- Dots and beads of
Cyanoacrylates Dots and beads of solvents Dots and beads of UV cure Dots and
beads of PVA glues Deposits of liquid fluxes Dots and beads of threadlockers.
Disclaimer: While reasonable efforts have been made to ensure all information
on this website is accurate, Adhesive Dispensing Ltd. do not assume
responsibility for any errors or omissions. All specifications, illustrations,
data and prices are subject to change without notice.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Ideal for cyanoacrylates
- High precision solution supplied complete
- Repeat dots, lines or potting of most liquids
- Adjustable stroke control for fine tuning of flow
- Syringe feed, cartridge feed or pressure pot
- Supplied with fluid lines and tip kit
- Easy bench mount, machine mount or robot mount
- Simple to control using TS500R, TS250 or TS350
- 1 Year Warranty
|
|
|
|
|
|
|
|
|
